Spray Dryer (ADL311S-A)
Easily micronize liquid samples with a spray dryer
Features of Spray Dryer (ADL311S-A)
- ADL311SA: For aqueous soluble samples (When organic solvent is used, a GAS410 organic solvent recovery unit is required.)
- Easy setup, easy
- Suitable for heat sensitive samples. High heat is not directly applied to dry, fine powder
- Obtain contaminant free fine powder which is not oxidized and contains minimal moisture
- Direct drying of solution or solution liquid into fine powder. No pre- or post processes such as filtration, separation, or pulverization required
- Safe and explosion free working is guaranteed in combination with GAS410 due to oxygen & pressure control
- Organic solvents are recovered in a closed loop to protect the environment to enable minimized pollution
- Easy operation with one-touch detachable mechanism for drying chamber and cyclone
- An arm jack is equipped as standard for easy installation and removal of glassware attachments
- A service outlet (max.2A) and a sample stand are equipped as standard for connecting a magnetic mixer for stirring suspended liquid samples
- Unique peristaltic pump, nozzle cooling mechanism, pulse jet mechanism and a nozzle knocker for stable spray drying
- ADL311SA is highly mobile on wheels, or usable with shorter height as a bench top unit by removing the movable caster operation
Specifications
Item Code | 212738 |
---|---|
Model | ADL311S-A |
Temp. adjusting unit setting range | 40 to 220°C (inlet temperature), 0 to 98°C (Outlet temperature) |
Temperature adjusting accuracy | Inlet temperature±1°C |
Drying air amount adjusting range | 0 to 0.7m3/min |
Spray air pressure adjusting range | 0 to 0.3MPa |
Liquid sending pump flow rate range | 0 to 26 mL/min |
Spray air line washing function | Spraying at the nozzle tip, Manual pulse jet system |
External output | Inlet temperature, Outlet temperature, Temperature outlet (4-20 mA) |
Temperature adjusting device | PID digital temperature adjusting device |
Touch panel | Blower, Heater, Liquid sending pump, Pulse jet switch, error display |
Control select switch | Inlet temperature, Outlet temperature control switch(Outlet temperature control is conditional) |
Temperature sensor | K-thermocouple |
Heater | 2.0kW (at200V) to 2.88kW (at240V) |
Liquid sending | Fixed amount peristaltic pump |
Spraying air pump | For water soluble samples air compressor is used (sold separately). For organic solvent samples the integrated compressor in GAS410 is used (No separate air compressor required). |
Service outlet | For stirrer: AC100V, MAX. 2A |
Suction blower | Bypass blower |
Filter | Suction filter, Exhaust filter |
Recovery of solvent | Solvent recovery unit GAS410 (Sold separately) is used |
Spray nozzle cooling mechanism | Connector: nipple×2, O.D.: ø10.5mm |
Spray air connection diameter | Nipple diameter: ø7mm |
Spray air pressure | Bourdon tube: 0.3 MPa |
Exhaust connecting diameter | ø50mm |
Safety function | Inlet / Outlet temperature overheat, Sample feed reverse rotation mechanism, Over current electric leakage breaker, Nozzle connection error |
External dimensions£¨W×D×H mm£© | 580×420×1125mm |
Power Source |
AC200-AC240V 16-18A Single phase |
Weight | 80kg |
Accessories | Silicon tubes (with a stopper)×3, Exhaust duct (with one hose band)×1, Outlet temperature sensor, Spray air tube, Sample box, Static electricity removal earth, ''Tetron'' braided tube hose 5m (with two hose bands) |
Maintenance and warranty
Conditions: temperature and humidity: 23 deg.C+/-5 deg.C, 65%RH+/-20% (no load)
External dimensions do not include protrusions.